Choosing the right control panel or enclosure for industrial automation often comes down to one question: are you building a panel from scratch, or buying a cabinet that already has the controls inside? The four options here cover both paths. At one end is a no-frills metal enclosure for housing your own components; at the other is a complete 208V 3-phase ABB control cabinet pulled from a steam boiler system. Prices run from $26.87 to $500, so the decision is more about matching the job than stretching a budget. For anyone working with control panels, enclosures, and DIN rail gear, the range matters more than the absolute numbers.
Quick Take
The table below sorts each option by listed price. The bars give a quick visual sense of how the prices compare before you think about what's included.
| Product | Listed Price | Price Bar |
|---|---|---|
| Industrial Control Panel Push Button station w/Emergency Stop | USD 35.00 | |
| SCE Industrial Control Panel Enclosure 8N806LP 8\" x 8\" x 6\" Nema-1 | USD 26.87 | |
| Industrial Control Panel Enclosure Stainless Steel IEC 24x20x11\" (6) Available | USD 130.00 | |
| Industrial Control Panel - ABB DP60C3P-1 Contactors - 208V 3-Phase - Steam Boil | USD 500.00 |
Decision Matrix
| If you need... | Pick this |
|---|---|
| A low-cost indoor metal shell to house your own controls | SCE 8N806LP NEMA 1 Enclosure |
| A ready-to-mount push button station with emergency stop | Industrial Control Panel Push Button station |
| A weather-resistant stainless enclosure for larger gear | IEC 24x20x11 Stainless Steel Enclosure |
| A complete 208V 3-phase control cabinet with contactors and relays | ABB DP60C3P-1 Boiler/Process Control Cabinet |
Product Notes
Industrial Control Panel Push Button station w/Emergency Stop
This used push button station comes from Automation Technologies Industries and is built in the United States. The selling point is the integrated emergency stop, which gives you a clearly identified manual cut-off at the machine. That makes it a simple way to add a control point or replace a damaged station without sourcing separate switches. The limitation is scope: it's a push button station, not a full panel, so you won't get contactors, relays, or a power distribution block. The used condition is the other trade-off, since it has prior service rather than being a new, unopened unit.
SCE Industrial Control Panel Enclosure 8N806LP 8\" x 8\" x 6\" Nema-1
This SCE enclosure is a metal, square NEMA 1 box made in the United States and sized 8 x 8 x 6 inches. With 23 units available, it works as a low-cost shell for a small indoor control panel or a dedicated junction box. The limitation is that it's used and shows minor scrapes, and the hinges vary between plastic and metal depending on the unit. Because it's a NEMA 1 design, it's intended for indoor service rather than wet or outdoor locations.
Industrial Control Panel Enclosure Stainless Steel IEC 24x20x11\" (6) Available
This new stainless steel enclosure is the weather-resistant pick. It's rated IP66 and includes dual quarter-turn latches, a silver stainless finish, and 24 x 20 x 11-inch external dimensions. Six are available, and the listing mentions bulk rates if you need more than one. The internal studs are there, but no backplates are included, so you'll need to add your own mounting plate. The trade-off is the larger size and higher price point, which make sense when you need water protection and stainless construction.
Industrial Control Panel - ABB DP60C3P-1 Contactors - 208V 3-Phase - Steam Boil
This is the only option in the group that arrives as a wired control cabinet rather than a bare enclosure or push button station. It's a used cabinet removed from a functioning 72 kW electric steam boiler system, and it includes four ABB DP60C3P-1 definite-purpose contactors, a control transformer with 120V secondary, relays 1CR through 4CR, terminal blocks, a wiring harness, and a metal enclosure with door. The internal wiring is described as clean, and the components are in new condition. What you give up is flexibility: it's built around 208V 3-phase power with 120V control, so it suits that voltage and boiler/process duty, and it's used rather than factory-fresh.
Final Recommendation
- For a budget shell that lets you build your own indoor panel, the SCE 8N806LP is the simplest starting point. It's small, metal, and the scrapes are a reasonable trade-off for the low entry price.
- For a machine-side push button station with a safety stop, the Industrial Control Panel Push Button station gets the job done without a full enclosure.
- For a protected stainless enclosure that can take a 24x20x11-inch setup, the IEC stainless steel unit is the clear choice when water resistance matters.
- For a ready-to-wire boiler or process control cabinet at 208V 3-phase, the ABB DP60C3P-1 panel is the only one in this list that comes complete with contactors, relays, and transformer.
